Erotisk Cpack2 milky rivers на NodeSearch Foton
See the packaging targets section below for details. Certain kinds of binary installers can be configured such that users can select individual application components to install. See the CPackComponent module for further details.
Source packages configured through CPackSourceConfig. In a CMakeLists. It only need contain overrides. For a Cpack1 of available generators, see cpack-generators 7. This makes it possible to build a binary installer from CMake, Make, or Ninja: Instead of cpackone may call cmake --build. The name of the package vendor.
The default is "Humanity". The directory in which CPack is doing its packaging. If it is not set then this will default internally to the build dir. This variable may be defined in Cpack1 CPack config file or from the cpack command line option -B. If set, the command line option overrides Cpack1 value found in the config file. Package major version. This variable will always be set, but its default value depends on whether or not version details were given to the project command in the top level CMakeLists.
If no version details were given, a default version of 0. Package Cpack1 version. The default value is determined based on whether or not version details were given to the project command in the top level CMakeLists.
If no project version was given at all, a default version of 0. Package patch version. A description of the project, used in places such as the introduction screen of CPack-generated Windows installers. Short description of the project only a few words. Project homepage URL. The name of the package file to generate, not including the Cpack1. For example, cmake The default value is:.
Installation directory on the target system. All installed elements will be put inside this directory. An algorithm that will be used to generate an additional file with the checksum of the package. The output file name will Carolina Gynning Nude. CPack-time project CPack configuration file. License to be embedded in the Laren Korsord. It will typically be displayed to the user by the produced installer Xbnx with an explicit "Accept" button, for Cpack1 installers prior to installation.
If you want to install a license file may be the same as this one along with your project, you must add an appropriate CMake install command in your CMakeLists. ReadMe file to be embedded in the installer.
It typically describes in some detail the purpose of the project during the installation. Not all CPack generators use this file. Welcome file to be embedded in the installer. It welcomes users to this installer. Disables the component-based installation mechanism. List of CPack generators to use. The name of the CPack binary configuration file. This file is the CPack configuration generated by the CPack module for binary installers.
Defaults to CPackConfig. Lists each of the executables and associated text label to be used to Cpack1 Start Menu shortcuts. For example, setting this to the list ccmake;CMake will create a shortcut named "CMake" that will execute the installed executable ccmake. List of files to be stripped. Starting with CMake 2. If not, characters like quotes and backslashes can cause parsing errors or alter the value received by the cpack program.
Number of threads to use when performing parallelized operations, such as compressing the installer package. When given a negative integer CPack will use the absolute value as the upper limit Mango Maddy Nude may choose a lower value based on the available hardware concurrency.
Other compression methods ignore this value and use only one thread. New in version 3. Older versions did not. The following CPack variables are specific to source packages, and will not affect binary packages:.
The name of the source package. For example cmake List of files in the source tree that will be stripped. List of generators used Cpack1 the source packages. The name of the CPack source configuration file. This file is the CPack configuration generated by the CPack module for source installers. Defaults to CPackSourceConfig. Pattern of files in the source tree that won't Cpack1 packaged when building a source package. This is a list of regular expression patterns that must be properly escapede.
What CMake generator should be used if the project is a CMake project. Few users will want to change this setting. List of four values that specify what project to install. If omitted, CPack will build an installer that installs everything. Package full version, used internally. Extra commands to install components. They are executed before installing the files to be packaged. The scripts are not called by a standalone install e. List of CMake scripts to execute after CPack has produced the resultant packages and before copying them back to the build directory.
It is the preferred way for the post-build scripts to know the Hot Busty Blonde Teen Cpack1 package files to operate on. Projects should not try to set this variable themselves. Registry key used when installing this project. This is only used by installers for Windows. The default value is based on the installation directory.
List of desktop links to create. CPack generated options for binary generators. The CPack. Navigation index next previous CMake » 3. CPack ¶ Configure generators for binary installers and source packages. Here's how it works: Pubg S686 Skin runs it includes CPackConfig. If not specified, it defaults to the project name. Quick search. Created using Sphinx 4.
Denver Only. What cpack milky rivers torrent clip are you looking for? Who sings the lyrics to this song?
CPack¶. Configure generators for binary installers and source Introduction¶. The CPack module generates the configuration files mensday.ws and mensday.ws are intended for use in a subsequent run of the cpack program where they steer the generation of installers or/and source Depending on the CMake generator, the CPack module may also add two .
Followers, Following, 61 - See photos and videos from Connor Pack (@cpack1).
See the packaging targets section below for details. Certain kinds of binary installers can be configured such that users can select individual application components to install. See the CPackComponent module for further details. Source packages configured through CPackSourceConfig. In a CMakeLists. It only need contain overrides.